4 Steps to Make Your Own Whimsical Woodland Napkin Ring
Share
Napkin rings are not only good for admiring and keeping your dinner napkins in place. They are actually quite the multipurpose little nick-knack. And fortunately sufficient, it is becoming easier to find them in a wide range of styles, shapes, colors, and designs. They are simple to make yourself.
This ring usually has a place at the dining room table, but it can also be used in your bedroom, as an exclusive home decoration, or thru the house during the holidays. It is ideal to find a reliable wedding and craft product supplier for buying ribbon, fabric, deco mesh, chair cover, tablecloth, favor bag, and many others.
Below, I’m going to share some steps for making your own whimsical woodland napkin ring that will go impeccably with the holiday or anytime when you want to put a little magic on your table.
Materials for Woodland Napkin Ring
- Artificial berries
- Artificial mushroom
- Moss
- Round wood slice
- Hemp twine
- Wood ring
- Satin ribbon
- Scissors
- Glue gun
Instructions to Make a Woodland Napkin Ring:
If you are going to start on this project, you should first check the list of materials and see if you missed anything. You don’t want to go consecutively around your home, annoying to find something or additional when your glue gun is hot, for instance. So, keep the whole thing ready. Let’s start.
Step 1: Wrap the Wood Ring
Begin by cutting out a good length of hemp wire. Then undo quite a bit of string and cut the pieces with scissors.
Now, plug the glue gun and add some hot glue to the wood. After that, start covering the hemp twine around the ring.
For making a tight wrap, ensure to push the twine rows together. Also, preserve adding hot glue to the wood ring by way of you go, so the hemp cord doesn’t end up affecting a lot on the ring.
Once more, use hot glue every now and then. You should do it every two turns and add just a bit more glue to it for covering all the twine completely.
Also make sure to twitch the rope close-fitting as you go around the ring, up to the end for preserving the tension.
Add a little bit more glue for covering the wood ring completely.
Now, you will have a beautifully hemp-wrapped wooden ring.
Step 2: Add the Wood Slice
Now, the wood ring is done, let’s add more hot glue. Start by picking a spot on the ring that may be one where the hemp twine doesn’t really sit properly.
Step 3: Decorate the Ring
In this step, start decorating the ring. And add some hot glue to the wood slice.
Bring in the moss and attach it using glue. You’re going to need to try to shelter as much of the hot glue as probable meanwhile you want the moss to appropriately twig to the wood. Also, ensure to preserve the pressure for a few seconds.
If necessary, then add more hot glue to apply the moss better.
Now, grab one of the decorative mushrooms and apply some hot glue to the wood ring and gently place the mushroom on top.
You should make sure to keep it pressed for a few seconds. Especially since this is bigger, then it needs more time to set.
After that, prepare the artificial berries and cut out the stems for the berries with your scissors.
Once they are done, use a glue gun and add some hot glue to the base of the ring and add them securely. You should carefully place the berries over the moss one by one.
Add some hot glue to the back of the berries too for sticking them perfectly. And also position the berries to kindly cover the wood slice of your napkin ring.
Step 4: Make a Bow
Now, take the ribbon and cut a good length with scissors.
Push one end of the ribbon over the ring and tie a lump. And after that, make a little bow out of material.
After making the bow, cut the tails at an angle to give the bow a nice finished look.
By using the above-mentioned steps make more than one napkin ring. You can find a leading fabric supplier for buying ribbons, tulle fabrics, organza fabrics, chair covers, table runners, favor bags, and many others.